rough finish
英 [rʌf ˈfɪnɪʃ]
美 [rʌf ˈfɪnɪʃ]
粗加工；粗饰
双语例句
- All the surfaces of ferrous metals exposed to the air which undergo rough machining or finish machining shall be cleaned with solvent and be treated against rust.
所有暴露在大气中的铁类金属粗加工或精加工表面在运输之前应经溶剂清洗干净，并进行防锈处理。 - Would you mind looking at my rough draft when I finish it?
我写完草稿后你不介意看看吧？ - Based on the geometry characteristic and processing technique of centrifugal compressor impeller, the tool path of rough and finish machining are scheduled.
分析了离心压气机叶轮的几何结构特点、加工工艺，并在此基础上规划了叶轮的粗、精加工刀具轨迹。 - It is shown that bending strength rises in the order of linear cutting, rough grinding, finish grinding, polishing, thermal treatment, coating once with Al 2O 3 sol, coating twice with Al 2O 3 sol, coating with composite Al 2O 3-SiO 2 sol.
结果表明，试样的抗弯强度按线切割、粗磨、精磨、抛光、热处理、氧化铝一次涂层、氧化铝二次涂层、Al2O3-SiO2混合涂层的次序依次提高。 - The results showed that the dynamic recrystallization occurred easily in higher temperature and lower strain rate, the static recrystallization developed perfectly in the former passes, and the effect of grain size refining in the rough rolling stage was stronger compared with that finish rolling.
研究结果表明：动态再结晶易在温度较高、应变速率较低的条件下发生；静态再结晶在前几道次发生的比较充分； - The process characteristics and applications of high speed milling is introduced, and the strategy of its application for rough, semi-finish and finish cutting is discussed in this paper.
介绍了高速铣削技术的工艺特点及其应用，并就高速铣削的粗加工、半精加工和精加工策略进行了探讨。 - In the machining process, the profile modeling method for lathe cutting cams is adopted, which resultes in satisfactory effects both in machining accuracy and in production rate, whether it is used in a rough machining or in a finish machining.
在机械加工工艺中，采用靠模法车削凸轮，无论是粗加工抑或精加工已是常见的加工方法，其加工精度和生产率都能令人满意。 - To introduce the production process technology of rough drawing, heat treatment and finish drawing of heavy coil steel wire and the transportation manner among procedures.
介绍大盘重粗拉、热处理、成品拉拔生产工艺技术以及各工序之间的运输方式，说明大盘重连续生产线的设计应从钢丝生产的总体流程考虑。 - The models of width control for rough mill includes hydraulic system and edger stand. The models of tension control for finish mill includes DC main driver system, AC main driver system and electric looper.
其中粗轧宽度压下模型又包括液压压下系统模型和立辊机架模型，精轧张力系统模型包括直流调速系统模型、交流同步调速系统模型、电动活套模型。 - After analysed and contrasted, it was proved that the technology can shorten the prepared period significantly. ( 2) It puts forward efficient planning technology of tool path for rough and finish machining.
经过分析对比，证明了该技术可大幅缩短技术准备周期。（2）论文提出了高效的粗、精加工刀位路径规划技术。 - On the basis of the analysis of the screw rotor form grinding process, the error control strategy that controls the divide error on rough grinding and profile error on finish grinding is presented.
分析了螺杆转子成形磨削加工过程，以此为基础提出了转子粗磨阶段控制分度误差，精磨阶段控制型线误差的误差控制策略。